[[bsnmpd FreeBSD 9.0]] #contents *HP ProLiant ML110 G7 [#u121d4d5] http://h50146.www5.hp.com/products/servers/proliant/system_pdf/ml110g7.pdf |フォームファクタ||マイクロATX| |電源||ATX電源 350W 70%効率 460W 92%効率 80PLUS Gold| |チップセット||Intel C204| |メインメモリ||2GB (最大16GB)| |メモリスロット||4| |メモリタイプ||PC3-10600 SDRAM、Unbuffered| |オンボードVGA||Matrox G200eH (16MB)| |||1600×1200 16bit| |||1280×1024 24bit| |PCI-Expressスロット|Gen2 x16|1| ||Gen2 x 4(x8コネクタ)|2| ||Gen2 x 1(x4コネクタ)|1| |PCIスロット||0| |SATAポート||2(光学ドライブ用だがHDD/SSDでも使用可能) (HDDは別コネクタ、SFF8087)| |IDEポート||0| |FDDポート||0| |シリアルポート||背面 1 D-sub 9ピン| |パラレルポート||0| |USBポート||9 (背面 4、前面 4、内部 1)| |SDカードスロット||1 (内部 1 USB接続)| |ネットワーク コントローラ||NC112i (Intel 82574L)x2| |内蔵サウンド||なし| |5.25inchベイ||2| |3.5inchベイ||0| |3.5inch HDD内蔵ベイ||4| |キーボード/マウス||USBキーボード/USBマウス| |PS/2端子||ナシ| |外形寸法(W×D×H mm)||175×473×367| |梱包サイズ(W×D×H mm)||499×599×337| |質量||(最大)17kg| |主な付属品||電源ケーブル×2| |||ドライバCD等| |||T15トルクスレンチ| |||↑ケース内5inchベイ横に装備| *G7 を監視するよ [#h2cbbf8f] G7の場合、ipmi 経由でCPU温度などを取得する(しかない?)らしいので、ipmiドライバを使えるようにする。 **ipmiドライバ [#efbd1263] http://nhh.mo-blog.jp/ttt/2008/11/freebsd_ml115_g_8313.html ipmiというドライバがを組み込む /boot/loader.confに ipmi_load="YES" とか入れておけばよさそうです。 ipmiはsmbusに依存しているようなので、ipmiとsmbusが組み込まれます。 # kldstat Id Refs Address Size Name 1 7 0xc0400000 62d184 kernel 2 1 0xc0a2e000 bf3c ipmi.ko 3 2 0xc0a3a000 2c20 smbus.ko 4 2 0xc0a3d000 6b2c4 acpi.ko 5 1 0xc65ff000 2000 green_saver.ko g7# kldstat Id Refs Address Size Name 1 21 0xffffffff80200000 11cd9b0 kernel 2 1 0xffffffff813ce000 203d70 zfs.ko 3 2 0xffffffff815d2000 5c50 opensolaris.ko 4 1 0xffffffff815d8000 17d8 accf_http.ko 5 1 0xffffffff815da000 29e0 coretemp.ko 6 1 0xffffffff815de000 fec8 ipmi.ko 7 2 0xffffffff815ee000 2620 smbus.ko g7# dmesg |grep impi g7# dmesg | grep ipmi ipmi0: <IPMI System Interface> port 0xca2-0xca3 on acpi0 ipmi0: KCS mode found at io 0xca2 on acpi ipmi0: KCS error: ff ipmi1: <IPMI System Interface> on isa0 device_attach: ipmi1 attach returned 16 ipmi1: <IPMI System Interface> on isa0 device_attach: ipmi1 attach returned 16 ipmi0: IPMI device rev. 1, firmware rev. 1.26, version 2.0 ipmi0: Number of channels 0 ipmi0: Attached watchdog ** ipmitool をインストール [#ab63a96e] g7# portinstall sysutils/ipmitool ** Found already installed package(s) of 'sysutils/ipmitool': ipmitool-1.8.11_4 (^_^; g7# ipmitool sdr UID Light | 0 unspecified | ok Health LED | 0 unspecified | ok VRM 1 | 0 unspecified | cr Power Supply 1 | 0 unspecified | nc Fan 1 | 54.88 unspecifi | nc Fan 7 | 46.65 unspecifi | nc Fan 8 | 10.19 unspecifi | nc 01-Inlet Ambient | 27 degrees C | ok 02-CPU | 40 degrees C | ok 03-P1 DIMM 1-4 | 32 degrees C | ok 04-P1 Mem Zone | 35 degrees C | ok 05-P1 Mem Zone | 33 degrees C | ok 06-HD Max | 50 degrees C | ok 07-VR P1 | 37 degrees C | ok 08-VR P1 | 45 degrees C | ok 09-VR P1 Zone | 35 degrees C | ok 10-VR P1Mem Zone | 31 degrees C | ok 11-PCI 1 Zone | disabled | ns 12-PCI 2 Zone | disabled | ns 13-PCI 3 Zone | disabled | ns 14-PCI 4 Zone | disabled | ns 15-System Board | 29 degrees C | ok 16-System Board | 32 degrees C | ok Memory | 0 error | ok g7# ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : previous Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false Front Panel Control : none freebsd ipmitool グラフ化 でググれ http://d.hatena.ne.jp/mteramoto/20090705/p3